Scaling effect of direct solar hot water systems on energy efficiency

U. C. Arunachala, M. Siddhartha Bhatt, L. K. Sreepathi

Research output: Contribution to journalArticle

5 Citations (Scopus)

Abstract

Scale formation in risers and header of direct solar hot water systems is a problem in places where hard water is being used. In this paper, the effect of scaling on energy efficiency indices such as instantaneous efficiency, mass flow rate, and overall heat loss coefficient are quantified by Hottel-Whillier-Bliss equation in the case of thermosiphon and forced circulation systems. The effect of scaling on mass flow and heat transfer rate for both the systems are quantified with experimental validation. Experimentally found mass flow rate is 50% of the analytical mass flow rate for a clean riser and agrees 99% for the case of riser with 3.75 mm scale thickness. This is due to the extreme change in pressure gain in the narrow region. Scale mapping is done for the entire solar hot water system to study the nature of scale growth. The complete footer and nine risers for the length of 150 mm from footer are free from scaling in axial and radial direction. This is due to the low water temperature in the region. The major portion of header and risers for the length 180 mm from the header are completely blocked due to maximum temperature of water in that region. A scale prediction model is brought out based on the experimentally observed scaled water heaters in the field. It reveals that the major parameters to be considered for the correlation are water total hardness and calcium hardness. It is seen in the thermosiphon system that the mass flow rate decreased by scaling affects energy efficiency more than that caused by the heat transfer rate. The scaling effect is more predominant in thermosiphon systems than in forced circulation systems. The analytical study reveals a drop in instantaneous efficiency of 39.5% in thermosiphon system and 7.0% in the case of forced circulation system for the scale thickness of 3.75 mm. The difference between mass flow rate in scaled and unscaled condition is less in forced circulation but much higher in thermosiphon system.

Original languageEnglish
Article number041012
JournalJournal of Solar Energy Engineering, Transactions of the ASME
Volume132
Issue number4
DOIs
Publication statusPublished - 01-12-2010

Fingerprint

Thermosyphons
Energy efficiency
Flow rate
Water
Hardness
Heat transfer
Water heaters
Heat losses
Calcium
Temperature

All Science Journal Classification (ASJC) codes

  • Energy Engineering and Power Technology
  • Renewable Energy, Sustainability and the Environment

Cite this

@article{c6d5c3e157544f99b875d526729351c9,
title = "Scaling effect of direct solar hot water systems on energy efficiency",
abstract = "Scale formation in risers and header of direct solar hot water systems is a problem in places where hard water is being used. In this paper, the effect of scaling on energy efficiency indices such as instantaneous efficiency, mass flow rate, and overall heat loss coefficient are quantified by Hottel-Whillier-Bliss equation in the case of thermosiphon and forced circulation systems. The effect of scaling on mass flow and heat transfer rate for both the systems are quantified with experimental validation. Experimentally found mass flow rate is 50{\%} of the analytical mass flow rate for a clean riser and agrees 99{\%} for the case of riser with 3.75 mm scale thickness. This is due to the extreme change in pressure gain in the narrow region. Scale mapping is done for the entire solar hot water system to study the nature of scale growth. The complete footer and nine risers for the length of 150 mm from footer are free from scaling in axial and radial direction. This is due to the low water temperature in the region. The major portion of header and risers for the length 180 mm from the header are completely blocked due to maximum temperature of water in that region. A scale prediction model is brought out based on the experimentally observed scaled water heaters in the field. It reveals that the major parameters to be considered for the correlation are water total hardness and calcium hardness. It is seen in the thermosiphon system that the mass flow rate decreased by scaling affects energy efficiency more than that caused by the heat transfer rate. The scaling effect is more predominant in thermosiphon systems than in forced circulation systems. The analytical study reveals a drop in instantaneous efficiency of 39.5{\%} in thermosiphon system and 7.0{\%} in the case of forced circulation system for the scale thickness of 3.75 mm. The difference between mass flow rate in scaled and unscaled condition is less in forced circulation but much higher in thermosiphon system.",
author = "Arunachala, {U. C.} and Bhatt, {M. Siddhartha} and Sreepathi, {L. K.}",
year = "2010",
month = "12",
day = "1",
doi = "10.1115/1.4002512",
language = "English",
volume = "132",
journal = "Journal of Solar Energy Engineering, Transactions of the ASME",
issn = "0199-6231",
publisher = "American Society of Mechanical Engineers(ASME)",
number = "4",

}

Scaling effect of direct solar hot water systems on energy efficiency. / Arunachala, U. C.; Bhatt, M. Siddhartha; Sreepathi, L. K.

In: Journal of Solar Energy Engineering, Transactions of the ASME, Vol. 132, No. 4, 041012, 01.12.2010.

Research output: Contribution to journalArticle

TY - JOUR

T1 - Scaling effect of direct solar hot water systems on energy efficiency

AU - Arunachala, U. C.

AU - Bhatt, M. Siddhartha

AU - Sreepathi, L. K.

PY - 2010/12/1

Y1 - 2010/12/1

N2 - Scale formation in risers and header of direct solar hot water systems is a problem in places where hard water is being used. In this paper, the effect of scaling on energy efficiency indices such as instantaneous efficiency, mass flow rate, and overall heat loss coefficient are quantified by Hottel-Whillier-Bliss equation in the case of thermosiphon and forced circulation systems. The effect of scaling on mass flow and heat transfer rate for both the systems are quantified with experimental validation. Experimentally found mass flow rate is 50% of the analytical mass flow rate for a clean riser and agrees 99% for the case of riser with 3.75 mm scale thickness. This is due to the extreme change in pressure gain in the narrow region. Scale mapping is done for the entire solar hot water system to study the nature of scale growth. The complete footer and nine risers for the length of 150 mm from footer are free from scaling in axial and radial direction. This is due to the low water temperature in the region. The major portion of header and risers for the length 180 mm from the header are completely blocked due to maximum temperature of water in that region. A scale prediction model is brought out based on the experimentally observed scaled water heaters in the field. It reveals that the major parameters to be considered for the correlation are water total hardness and calcium hardness. It is seen in the thermosiphon system that the mass flow rate decreased by scaling affects energy efficiency more than that caused by the heat transfer rate. The scaling effect is more predominant in thermosiphon systems than in forced circulation systems. The analytical study reveals a drop in instantaneous efficiency of 39.5% in thermosiphon system and 7.0% in the case of forced circulation system for the scale thickness of 3.75 mm. The difference between mass flow rate in scaled and unscaled condition is less in forced circulation but much higher in thermosiphon system.

AB - Scale formation in risers and header of direct solar hot water systems is a problem in places where hard water is being used. In this paper, the effect of scaling on energy efficiency indices such as instantaneous efficiency, mass flow rate, and overall heat loss coefficient are quantified by Hottel-Whillier-Bliss equation in the case of thermosiphon and forced circulation systems. The effect of scaling on mass flow and heat transfer rate for both the systems are quantified with experimental validation. Experimentally found mass flow rate is 50% of the analytical mass flow rate for a clean riser and agrees 99% for the case of riser with 3.75 mm scale thickness. This is due to the extreme change in pressure gain in the narrow region. Scale mapping is done for the entire solar hot water system to study the nature of scale growth. The complete footer and nine risers for the length of 150 mm from footer are free from scaling in axial and radial direction. This is due to the low water temperature in the region. The major portion of header and risers for the length 180 mm from the header are completely blocked due to maximum temperature of water in that region. A scale prediction model is brought out based on the experimentally observed scaled water heaters in the field. It reveals that the major parameters to be considered for the correlation are water total hardness and calcium hardness. It is seen in the thermosiphon system that the mass flow rate decreased by scaling affects energy efficiency more than that caused by the heat transfer rate. The scaling effect is more predominant in thermosiphon systems than in forced circulation systems. The analytical study reveals a drop in instantaneous efficiency of 39.5% in thermosiphon system and 7.0% in the case of forced circulation system for the scale thickness of 3.75 mm. The difference between mass flow rate in scaled and unscaled condition is less in forced circulation but much higher in thermosiphon system.

UR - http://www.scopus.com/inward/record.url?scp=79953249818&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=79953249818&partnerID=8YFLogxK

U2 - 10.1115/1.4002512

DO - 10.1115/1.4002512

M3 - Article

VL - 132

JO - Journal of Solar Energy Engineering, Transactions of the ASME

JF - Journal of Solar Energy Engineering, Transactions of the ASME

SN - 0199-6231

IS - 4

M1 - 041012

ER -